Panasonic AJ-PX230 Series, Operating Instructions Manual

Page: 145 / 169

– 145 –
Chapter 7 Display — Screen status display
32 Battery charge level indicator
As the battery level decreases, the indication changes → → → → → .
When the battery runs out, ( ) flashes.
(When the camera is running on the AC adaptor, is displayed.)
The battery charge level may not be indicated correctly in a place where the temperature is extremely low or high, or when the camera has not been
used for a long period of time. To display the remaining battery level correctly, fully charge the battery, use the camera until the battery runs out, and
then charge again. (Even after performing the procedure, the remaining battery may not be indicated correctly if the battery is used under extremely
low or high temperature for a long period of time or if the battery has been repeatedly recharged.)
Note that the time in the battery charge level indicator is an approximate estimate as it changes according to the conditions of use.
33 microP2 memory card remaining capacity
f
: This is the slot No. This is displayed in black and white inversion when the slot No. is recording destination. It flashes while the card is being
recognized.
f
[
***
min]: Displays the remaining space on the media in each slot. During a near end, it flashes.
f
(No display): Not displayed when a card is not inserted.
f
[END]: Displayed when there is no space remaining on each card.
f
[WP]: Displayed when the microP2 memory card is write-protected.
f
[ERR]: Displayed in case of format errors or authentication errors.
f
[LOOP
***
min]: Displayed when the loop recording mode is set. During the mode check, the second line displays the standard recording time of
loop recording. [LOOP] flashes when loop recording is not possible, for example, when there is no more space remaining on the microP2 memory
card.
34 Simultaneous recording mode display, background recording mode display
f
[SIMUL]: Displayed when the simultaneous recording is set. When the simultaneous recording cannot be performed, [SIMUL] indication is
displayed with a diagonal line.
f
[BACKGR]: Displayed when the camera is in the background recording mode and background recording is being performed on slot 2. When
background recording has not started on slot 2, the [BACKGR] indication is displayed with a diagonal line.
35 High-sensitivity mode display
Displayed when [HIGH SENS.] is set in the main menu → [SYSTEM MODE] → [SHOOTING MODE].
36 One clip recording mode status display
f
[1-CLIP]: The status where a new clip is to be recorded in one-clip recording
f
[1
*
CLIP]: The status where recording can be performed by combining to the previous clip in one-clip recording
37 Recording/playback operation status display
f
[REC]*
1
: Recording
f
[PAUSE]: Recording standby
f
[
&
]: Playback pause
f
[
=
]: Playback
f
[
&=
] ([
~&
]): Frame-by-frame playback (frame-by-frame rewind)
f
[
)
] ([
%
]): Fast-forwarding/fast-forward playback (fast-reversing/fast-reverse playback)
f
[CLIP
&=
] ([CLIP
~&
]): Clip forwarding (clip rewinding), cueing up by clips
f
[CLIP&T
&=
] ([CLIP&T
~&
]): Cueing up (rewinding) by clip and text memo (when [CLIP&TEXT MEMO] is set in the main menu → [OTHER
FUNCTIONS] → [SEEK POS SEL])
f
[START]*
1
: Displayed when recording of a new clip is started in one-clip recording.
f
[END]*
1
: Displayed when combining of clips is ended in one-clip recording.
f
[L-]*
2
: Loop recording
f
[I-]*
2
: Interval recording, one-shot recording
f
[P-]*
2
: Pre-recording
*1 If the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shot
recording is set, it is displayed.
*2 Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu → [RECORDING SETUP] → [RECORDING], or when [ON] is set in the
main menu → [RECORDING SETUP] → [PRE REC].
38 <AUTO/MANUAL> switch operation display
Displayed when the <AUTO/MANUAL> switch is set to <AUTO>.
39 GPS display
Displays the strength of the GPS signal reception in four levels. The GPS signal strength is indicated by the number of vertical bars. It is not
displayed when GPS is disabled.
40 HD SDI REMOTE recording status
Displays the control status of whether recording has started or stopped for an external device which is connected to the <SDI OUT> terminal.
When the main menu
→ [OUTPUT SEL] → [HD SDI REMOTE] is set to [ON], it will always be displayed regardless of the settings in the main menu
→ [DISPLAY SETUP]. It is not displayed when [HDSDI REMOTE] is set to [OFF].
f
[SDI
n
]: Status where the recording is being instructed for an external device
f
[SDI
&
]: Status where recording stop is being instructed for an external device
41 Audio monitor volume adjustment display
Displayed when the <AUDIO MON/ADV> button is pressed for volume adjustment of speaker or headphones. The display disappears three seconds
after the operation.
42 Front audio level volume display
The volume is displayed for three seconds when it is adjusted with the <F.AUDIO LEVEL> dial.
Camera status display
These are indicated in the information display area in the center.