Panasonic AJ-HD3700H Operating Instructions Manual Download

Page: 94 / 204

– 94 –

INSERT/ASSEMBLE MANUAL EDIT SET UP menu

∑

Selecting the SOFTWARE inhibit channels

(1) Press the center cursor key. The cursor now appears.

(2) Press the cursor key to move the cursor to the channel where editing is to be inhibited.

(3) Press the center cursor key. Once the display appears in reverse video, the selection of the

editing inhibit channel is completed. When the center cursor key is pressed again, the editing
inhibit is released.

(3)

≥

Assembly editing cannot be selected if there is even one editing inhibit channel.

Notes

≥

When ALL or PRE CTL has been set for CASSETTE EDIT REC INHIBIT or HOME REC IN-
HIBIT, all recording and editing operations will be inhibited.

≥

When VIDEO/CNTL has been set for CASSETTE EDIT REC INHIBIT, editing inhibit applies to
the video channel at all times.

∑

REC ENV display

This shows the RF envelope level at which sound is played back from the rotary recording heads during
playback.

CH4

Center cursor key

Cursor key

5
4
3
2
1

Summary of Contents for AJ-HD3700H













































































































































































































Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands

Panasonic AJ-HD3700H, Operating Instructions Manual

Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands