Panasonic AJ-HD3700H Operating Instructions Manual Download

Page: 173 / 204

– 173 –

AUTO OFF error messages

Message

CPU TAPE HANDLE
TROUBLE

CPU (SERVO SYS) COMM.
TROUBLE

CASSETTE PHOTO
SENSOR TROUBLE

DETECTION SWITCH FAIL
(A)

DETECTION SWITCH FAIL
(B)

DETECTION SWITCH FAIL
(C)

ROTATE-RANGE OVER

CAPSTAN NOT ROTATE

TAPE TENSION ERROR

TAPE TENSION OVER-
RANGE IN SHTL

REEL DIRECTION
UNMUTCH

WIND-UP REEL NOT
ROTATE

NO S-REEL FG PULSE

NO T-REEL FG PULSE

CASSETTE UNLOAD FAIL

SUB UNLACING FAIL

MAIN UNLACING FAIL

DEW

Error description

The CPU is not working properly due to an error
in the interrupt processing, etc.

A problem has occurred in communication
between the servo microcomputer and system
control microcomputer.

A problem with the LED has been detected.

There is a problem with the cassette’s 3-stage
switch (A) (on the cylinder side).

There is a problem with the cassette’s 3-stage
switch (B) (middle position).

There is a problem with the cassette’s 3-stage
switch (C) (on the cassette insertion slot side).

A problem with the cylinder’s rotation has been
detected.

A problem with the capstan’s rotation has been
detected.

A tape tension error has been detected. (Pinch
roller ON status) Check the tape transport
system.

A tape tension error has been detected. (Reel
drive status with pinch roller OFF) Check the
tape transport system.

A discrepancy in the rotational directions of the
supply and take-up reels has been detected.
Check the tape transport system.

Defective rotation of the take-up reel has been
detected. (During capstan drive) Check the tape
transport system.

Trouble with the rotation of the supply reel has
been detected.

Trouble with the rotation of the take-up reel has
been detected.

A problem with the cassette “up” operation has
occurred. Check the tape transport system.

A problem with the sub-unloading operation has
occurred. Check the tape transport system.

A problem with the main unloading operation
has occurred. Check the tape transport system.

The formation of condensation has been
detected. Refrain from inserting a cassette since
this condition may cause the tape to adhere to
the inside parts, etc., thereby damaging it.

On-screen display

SYSCON ERROR

SERVO ERROR

MECHA ERROR

SERVO ERROR

MECHA ERROR

Summary of Contents for AJ-HD3700H













































































































































































































Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands

Panasonic AJ-HD3700H, Operating Instructions Manual

Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands