Panasonic AJ-HD3700H Operating Instructions Manual Download

Page: 74 / 204

– 74 –

TC/CHR menu

∑

Time code displays and VTR’s operating modes (continued)

VTR’s operating modes

STOP

F.FWD

PREVIEW

REW

REVIEW

EDIT PLAY (edit playback)

PREROLL

EDIT REC (edit recording)

AUTO EDIT (automatic editing)

CUE UP

JOG

STANDBY OFF

VAR

EJECT

SHTL

DMC PREVIEW

REC

DMC EDIT

REC
(display blinks during Pre-CTL operation)

OUT PREVIEW

PLAY

DMC SAMPLE
(variable memory speed sampling underway)

P PLY (programmed playback)

DMC PLAY (variable memory playback underway)

TSO (TAPE SPEED OVERRIDE)

AUTO OFF

≥

In the shuttle/variable mode and CUE UP and PREROLL modes, the tape travel direction is in-
dicated as “

” or “

”, and the tape speed is displayed as an integer.

≥

In the jog mode, the tape travel is indicated by “

” when it is moving in the forward direction,

by “

” when it has stopped, and by “

” when it is moving in the reverse direction.

≥

In the programmed playback and TSO modes, “

” or “

” is used to indicate the deviation di-

rection, and the deviation data is displayed as a percentage.

∑

Error information displays

Press the F12 (SUPER ER) key to set it ON.

The error information will now be displayed.

FAN STOP

(fan stopped)

HD REF ERROR

(no HD reference signal input)

ERASE ERROR

(erase current stopped)

SD REF ERROR

(no SD reference signal input)

COMP.CPU ERROR

HD SDI ERROR

(HD SDI signal error)

(error in communication with CPU)

CONCEAL SW OFF

SD SDI ERROR

(SD SDI signal error)

(conceal SW at “OFF” position)

ECC SW OFF

(ECC SW at “OFF” position)

FREQ UNMATCH

(frequency settings fail to match)

SERVO UNLOCK

(no servo lock)

VIDEO ERROR

(video system error)

CTL NOT DET.

(no CTL signal detection)

PCM ERROR

(PCM signal system error)

LOW RF

(drop in RF level during recording)

RS-422 ERROR

(RS-422 system error)

CONCEAL V/A

(video/audio error corrected)

RS-232C ERROR

(RS-232C system error)

CONCEAL A

(audio error corrected)

VA-CONT ERROR

(VA controller error)

CONCEAL V

(video error corrected)

TC ERROR

(time code error occurred)

AUDIO MUTE

(audio output muted)

CARD LOW BATT

(low charge in front IC card battery)

HIGH ERROR

(inner error value too high)

SYSCON ERROR

(system control system error occurred)

CTL HEAD CLOG

(CTL head clogged)

MECHA ERROR

(mechanical system error occurred)

LTC HEAD CLOG

(LTC head clogged)

SERVO ERROR

(reel, drum or capstan error occurred)

OPT ERROR

(optimization system error)

SYSTEM ERROR

(other error)

Summary of Contents for AJ-HD3700H













































































































































































































Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands

Panasonic AJ-HD3700H, Operating Instructions Manual

Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands