Panasonic AJ-HD3700H Operating Instructions Manual Download | Manualshive

Page: 114 / 204

background image

– 114 –

INTERFACE SET UP menu

Key

F7

F8

F9

F10

F11

F12–F13

Key designation

PREREAD
For setting pre-read from
the remote commands.

EXIT

UB PRESET
For setting the UB preset
from remote.

VAR LIMT

°

V. LEV. CNT

——

Description

The setting can be changed by pressing the F7 key while holding
down the F key.

VIDEO:

Video pre-read can be set.

AUDIO:

Audio pre-read can be set.

V&A:

Both video and audio pre-read can be set.

Returns the VTR to the SET UP menu screen.

Selects the setting destination for the TCG UB preset command
supplied from the external source (RS-422/232C).

L&V:

Sets the destination for LTC UB and VITC UB.

LTC:

Sets the destination for LTC UB only.

VITC:

Sets the destination for VITC UB only.

Selects the limit speed for the VAR command supplied from the
external source (RS-422/232C).
This item can be set by pressing the F10 key and F key together.

ON:

The tape speed is limited to the range from

j

1x to

i

2x

normal speed.

OFF:

The tape speed is limited to the range from

j

1.5x to

i

2.5x normal speed. (At speed above 2x or so or below

j

1x, pictures are searched without AT ON TRACK.)

Selects whether to vary the VTR HD/SD output in response to an
external video component adjustment command (RS-422, V/A
controller).

NORMAL:

Identifies HD/SD commands and varies the level of
each.

HD:

Varies HD output level forcibly.

SD:

Varies SD output level forcibly.

BOTH:

Varies This is varied in tandem with the HD
output/SD output level.

°O

Note

N

°

Set this item to OFF for slow editing with the unit connected to an editing controller (such as the BVE-9100).
Phase synchronization may not be possible with slow editing near the

j

1x or

i

2x speed.

«
...
112
113
114
115
116
...
»

Summary of Contents for AJ-HD3700H













































































































































































































Reviews:

No comments

Related manuals for AJ-HD3700H

Brand: Go-Video Pages: 56

Brand: Emerson Pages: 8

Brand: Emerson Pages: 16

Brand: Emerson Pages: 16

Brand: Emerson Pages: 82

Brand: Emerson Pages: 8

Brand: JVC Pages: 64

Brand: Matsui Pages: 20

Brand: RGB Spectrum Pages: 14

Brand: RCA Pages: 36

Brand: Zenith Pages: 44

OmniVision PV-Q1311W

Brand: Panasonic Pages: 40

Brand: Samsung Pages: 77

Brand: Panasonic Pages: 84

Brand: Philips Pages: 54

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands