Panasonic AJ-HD3700H Operating Instructions Manual Download

Page: 143 / 204

– 143 –

RF adjustment value display menu

F13

F12

F11

F10

Key

F1–F5

F8–F10

F11

F12

Key designation

——

ADJ MODE
Adjust mode.

ADJ CH

——

ADJ RF
RF adjustment value
display.

ADJ SEL

Description

FIX:

Holds the current adjusted value. Parameter can be
readjusted by remote adjustment but the value cannot be
changed with this unit.

Selects the channel for display.

EQ/REC/PLL:

CH0, CH1, CH2, CH3

When the F11 key is pressed, ADJ SEL is displayed at the F12
key and the current adjusted value of the selected parameter is
displayed. Selects adjustment mode with F6 key and channel
with F7 key.

This is used to display the selected RF adjusted value.

EQ:

The adjusted value of the playback equalizer is displayed.

REC:

The recording adjusted value is displayed.

PLL:

The PLL relative speed adjusted value is displayed.

Pressing the F12 key enables switching by a toggling action in
the following sequence:

¢¢¢¢

PLL

¢¢¢¢

REC

¢¢¢¢

and so on.

Pressing the F key and F12 key together enables switching by a
toggling action in the following sequence: 6014

¢¢

6018

¢¢

501

¢¢

24P

¢¢

6014

¢¢

and so on.

The RF system adjusted values for each format are displayed as
these adjusted values. (They are used by the servicing
engineer.)

Summary of Contents for AJ-HD3700H













































































































































































































Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands

Panasonic AJ-HD3700H, Operating Instructions Manual

Search results

Summary of Contents for AJ-HD3700H

Reviews:

Related manuals for AJ-HD3700H

Brands by name

Popular brands