Panasonic 5054 Technical Manual Download

Page: 6 / 37

Technical Manual

5054 Rev 0

For Firmware V2.0.x

A termination resistor 120R has to be connected in the last unit on the RS485 bus. In 5054

units, this is done via jumper "J7" or “J3”. ("J7" shunted = the termination resistor is

connected.)

1.2 Power supply

The three tables below are some examples of the minimum cable length and type

requirements to use in display unit wiring.

1.2.1 Joint communication and power supply in twisted pairs, shielded,

RS485-cables

Cable (nearest size)

Type

Distance to unit

Belden 1419A, 2pr

1 pair of Communication & 1 pair of power

150 m

Belden 1420A, 3pr

1 pair of Communication & 2 pairs for power

300 m

Belden 1421A, 4pr

1 pair of Communication & 3 pairs for power

450 m

Belden 1212F, 4pr

1 pair of Communication & 3 pairs for power

400 m

1.2.2 Separate communication cable

Communication Cable

Type

Distance to unit

Belden 1419A, 2pr

1 pair of Communication (RS485)

1200 m

Belden 1421F, 4pr

1 pair of Communication (Cat5e F/UTP)

1200 m

Belden 7703NH, 1pr

1 pair of Communication (LonWorks)

1200 m

Note

: Maximum cable length for communications is 1200 m irrespective of the cable type. Brooks

recommend to use higher gage shielded cables for communications e.g. 0.7 mm² or 1.0 mm².

1.2.3 Separate power supply cable

Power Cable

Type

Distance to unit

Belden 5120UL, 14#

1 pair for power supply (Fire Alarm 14#)

1600 m

Belden 5220UL, 16#

1 pair for power supply (Fire Alarm 16#)

1000 m

Draka ELQYB, 2x1

1 pair of power supply (COM-loop)

500 m

Note

: As the limitation for communication cable length is max 1200 metre, it is recommended to

use 1.5mm² for the power supplied to display units.
The display unit has two screw terminal blocks for cable connections.

Note

: The current consumption of 5054 units is higher than the older style 1728 or 1736. Current

calculation must be performed based on the number of units that can be connected to the FDCIE.

The FDCIE can supply power to a maximum of 4 display units, additional units require external

power supply.

1.3 USB Interface

The display unit is equipped with an USB interface (X2) to directly download the firmware

and file system to the display unit via EBLWin.

Summary of Contents for 5054






































Search results

Summary of Contents for 5054

Reviews:

Related manuals for 5054

Brands by name

Popular brands

Panasonic 5054, Technical Manual

Search results

Summary of Contents for 5054

Reviews:

Related manuals for 5054

Brands by name

Popular brands