Installing the water heater.
This water heater must be installed in accordance with these instructions, local codes, utility company
requirements, and/or in the absence of local codes, use the latest edition of the American National
Standard/National Fuel Gas Code. A copy can be purchased from either the American Gas Association,
400 North Capitol Street Northwest, Washington, DC 20001 as ANSI standard Z223.1 or National Fire
Protection Association, 1 Batterymarch Park, Quincy, MA 02269 as NFPA 54. In Canada, the latest
edition of the CSA B149.1 Natural Gas and Propane Installation, and the Canadian Electrical Code,
CSA C22.1 Part 1, in the absence of local codes.
Location
The water heater should not be located
in an area where leakage of the heat
exchanger or connections will result in
damage to the area adjacent to it or to
lower floors of the structure.
When such areas cannot be avoided it is
recommended that a suitable catch pan,
adequately drained, must be installed
under the water heater.
The pan must not restrict combustion
air flow.
A gas fired water heater or any other
appliance should not be installed
in a space where liquids which give off
flammable vapors are to be used or stored.
Such liquids include gasoline, LP gas
(butane or propane), paint or adhesives and
their thinners, solvents or removers.
Because of natural air movement in a
room or other enclosed space, flammable
vapors can be carried some distance from
where their liquids are being used or
stored. The open flame of the water
heater’s main burner can ignite these
vapors causing an explosion or fire which
may result in severe burns, death or
property damage.
The water heater must be located so it is
not subject to physical damage, for example,
by moving vehicles, area flooding, etc.
If the water heater is installed in a garage,
it should be installed so that the direct
ignition system and main burner are no
less than 18 inches above the garage floor.
Raising the gas fired water heater will
reduce BUT NOT eliminate the possibility
of lighting the vapor of any flammable
liquids which may be improperly stored or
accidentally spilled.
●
The water heater should be installed as
close as practical to the vent termination
to minimize vent length and the number
of elbows required for venting.
●
The water heater should be installed
with the proper venting materials and
termination suitable for Category III
venting.
●
Failure to install and properly venting
the water heater to the outdoors as
outlined in the Venting Section of this
manual can result in unsafe operation.
●
Long hot water lines should be insulated
to conserve water and energy.
●
The water heater and water lines should
be protected from exposure to freezing
temperatures.
●
Do not
install the water heater in
bathrooms, bedrooms, any occupied
rooms normally kept closed, or in
outdoor areas.
●
Do not
install the water heater in small,
poorly ventilated rooms, or in air tight
rooms with air-conditioning.
●
Do not
install water heater where
subject to vibrations.
●
Do not
install the water heater in
Recreational Vehicles, Mobile Homes,
Boats and other Watercrafts.
●
Do not
install the water heater near
vents for heating or cooling.
●
Minimum clearance from combustible
construction is 1/2” sides, 0” rear (with
support bracket); 12” from the bottom;
12” from the front of the water heater;
and 12” from the top (24” from front
and top is recommended for servicing
purposes). Maintain a minimum
clearance of 2” around the vent pipe to
combustible construction. If the
clearances stated on the
Instruction/Warning Label, located on
the front panel of the heater differ,
install the water heater according to the
clearances stated on the label.
7
WARNING: Combustible
construction refers to
adjacent walls and ceilings
and should not be confused
with combustible or
flammable products and
materials. Combustible
and/or flammable products
and materials should never
be stored in the vicinity of
this or any gas appliance.
!
min.
1/2 "
min.
1/2 "
min. 12"
(24" minimum is
recommended for service)
Top = 12"
Vent = 2"
Front = 12"
min. 2"
min. 2"
Back = 0" (with support bracket)
Side = 1/2"
Bottom = 12"
Minimum Clearance
from
Combustible Construction
Vent Pipe
3" min
2" min
2" min
