manualshive.com logo in svg

Pall Allegro, Instructions For Use Manual

Share
Download
Pall Allegro Instructions For Use Manual Download Page 26

The below listed items are recommended spares, which should be checked and may replaced
as part of a routine service.

Recommended Spares

Part Number

Description

DC201772C00

Support arm/seal housing microswitch (200 L mixer tote)

DC201773C00

Door magentic switch (200 L mixer tote)

DC201774B00

UCI cabinet key

DC201775B00

Tote/lock key

KDC201340C00

Tube support assembly

DC200694C00

Support arm

DC201385C00

Motor and gearbox assembly

LGRMXUCI200L230

UCI (230 V)

LGRMXUCI200L120

UCI (120 V)

The below listed items are optional items and other spares.

Optional Spares

Part Number

Description

LGRMXBK200L

Baffle kit

LGRMXPBS200L

Powder bag support frame

10. WEEE Compliance. Reuse, Recycling and Recovery (2002/96/EC)  

The presence of this label on a product means that the product contains electrical or electronic
materials and therefore should not be disposed of as unsorted waste but instead treated
separately. The presence of these materials may, if not disposed of properly, have potential
adverse effects on the environment and human health. Within the European Union users are
urged to recycle such products when being replaced with a newer version or when they have
outlived their useful lives. However as the legislation and facilities vary throughout the member
states, please contact your local Pall sales office or distributor to discuss the available options
for correctly disposing of this product.

11. Warrantee 

Pall warrants that Allegro hardware and systems manufactured by Pall, when properly stored
and installed, and operated at ratings, specifications and design conditions, will be free from
defects in material and workmanship during their shelf life. 
Pall liability under any warrantee is limited solely to replacing, or issuing credit for the Allegro
systems and hardware that may become defective during the Warrantee Period. 

26

USD 2743

Summary of Contents for Allegro





























Reviews:

No comments

Brands by name

Popular brands

Load more brands