Pall Allegro Instructions For Use Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

System Installation

1. Install Allegro single-use system into the mixer tote.

A. Holding the system securely as shown below (Figure 12) align the shaft on the single-

use system, with the tube support in the centre of the mixer tote and the inlet port
plate to the right hands side of the impeller cover.

Figure 12

Holding the system (top left) ready to place system impeller shaft into the tube support mechanism
(top right) on the mixer tote and showing the system installed with doors open (bottom)

10

USD 2743

«
...
8
9
10
11
12
...
»

Summary of Contents for Allegro





























Reviews:

No comments

Related manuals for Allegro

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

Brand: Nakayama Pages: 37

Brand: Rain-Flo Irrigation Pages: 16

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: P-Q Controls Pages: 5

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Abbott Pages: 64

Brand: Gako Pages: 22

Brand: ABB Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands