Palax Power 100S Operating Instructions Manual Download Page 9

Page: 9 / 37

Palax Power 100S

Translation

1-2017

1.6 The main dimensions and models of the machine

Machine model

Power 100 s

DRIVING POWER

Weight

1,780 kg

1,850 kg

Height/width/length Transport

position 2.55 m / 1.75m / 3.2m

In-feed conveyor

Length 2.4m Height 0.9 m

Diameter of blade/hole

1000mm/ 40 mm

Max. rotation speed of blade

1000 r.p.m.

Max. diameter of the log

Max. cutting diameter of the log 40cm

Max./min. length of the log

The maximum length of log that can be split is 55 cm.



The 4.3 m firewood conveyor is included in the weight.

1.7 Safety

instructions

General regulations and restrictions



The maximum length of log that can be cut is 4 metres. If no log-stand or log-deck is
used.



The machine is exclusively intended for the production of firewood.



The machine may only be operated by one person.



The machine must be equipped with additional lights for transportation on public roads.



The danger zone around the conveyor is 5 metres to the sides and to the rear



Lift and lock the infeed deck and the discharge conveyor in the transport position for
transportation.



Only persons over 18 years of age are allowed to operate this machine.



Never remove any safety-related devices from the machine.

The operator



Every person operating the machine, must thoroughly study the entire user manual.



Always use eye guards and hearing protectors.



Always wear protective shoes.



Always wear work gloves.



Do not wear loosely-fitting clothing.

Before use



Always carry out the required preparations on both the machine and the conveyor be-
fore starting the operation.



Make sure that all other people stay outside the operating range.



Only use a fault-free PTO shaft and attach the chain for the shaft-guard. The permissi-
ble revolutions range of the power take-off shaft is 450–480 r.p.m.



Only operate the machine on a sufficiently firm and level surface.



Only operate the machine in an adequately lit space.



Keep the tractor-powered machine attached to one of the lifting arms. Also ensure that
sufficient space is provided for the PTO shaft and its guard.



Always check that all the covers are intact and properly fastened.



Always check that the crosscut saw-bar is intact.



Always ensure that the electric conductors are intact.



Always check that all the controls are operational.

Summary of Contents for Power 100S






































Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands

Palax Power 100S, Operating Instructions Manual

Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands