Palax Power 100S Operating Instructions Manual Download Page 2

Page: 2 / 37

Palax Power 100S

Translation

1-2017

CONTENTS

Basic specifications and responsibilities

......................................................................... 4

1.1

Foreword

............................................................................................................................... 4

1.2

EU Declaration of Conformity

............................................................................................ 5

1.3

Intended use of the machine

.............................................................................................. 6

1.4

Warning signs

....................................................................................................................... 6

1.5

Nameplates

........................................................................................................................... 8

1.6

The main dimensions and models of the machine

......................................................... 9

1.7

Safety instructions

................................................................................................................ 9

1.8

Noise emission and vibration

........................................................................................... 10

1.9

Responsibilities of the operator

....................................................................................... 10

1.10

Operating conditions

...................................................................................................... 10

1.11

Terms of warranty

........................................................................................................... 11

1.12

Operating instructions for the winch

............................................................................ 11

Taking delivery and setting up the machine for operation

.......................................... 12

2.1

Lifting the machine

............................................................................................................. 12

2.2

The transport set-up and unpacking

............................................................................... 12

2.3

Acceptance inspection

...................................................................................................... 12

2.4

Main parts of the machine

................................................................................................ 13

Setting up the machine for operation and transportation

............................................ 15

3.1

Table extension

.................................................................................................................. 15

3.2

Setting the log-stop

............................................................................................................ 15

3.3

Bringing the conveyor in work position

........................................................................... 16

3.4

Bringing the conveyor in work position

........................................................................... 18

......................................................................................................... 19

4.1

Installation

........................................................................................................................... 19

4.2

Emergency stop switch for a tractor-powered machine

............................................... 21

4.3

Required measures in an emergency situation

............................................................. 22

4.4

Transporting the machine by trailer (Fig. 19)

................................................................ 22

Operating the firewood processor

.................................................................................. 23

5.1

Electric drive, start and emergency stop.

....................................................................... 23

5.2

Control of the machine

...................................................................................................... 23

5.3

Use of the firewood processor, crosscut operation

...................................................... 23

5.4

Operating the crosscut saw, before the operation

........................................................ 24

5.5

During the operation

.......................................................................................................... 24

5.6

Placing the wood on the deck

.......................................................................................... 24

5.7

Crosscut operation

............................................................................................................. 24

5.8

Cutting the last log

............................................................................................................. 25

5.9

Feeding the last log for splitting

....................................................................................... 25

5.10

Disturbances during crosscut operation and their remedy

...................................... 26

Summary of Contents for Power 100S






































Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands

Palax Power 100S, Operating Instructions Manual

Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands