Palax Power 100S Operating Instructions Manual Download Page 8

Page: 8 / 37

Palax Power 100S

Translation

1-2017

Take care that the log is not in an upright position
when being fed for splitting

Dismantle the blade using the
key delivered with the machine

Adjusting the discharge conveyor's speed

Adjusting the crosscut saw-
blade's lowering speed



Refer to pages 13 and 14, chapter 2.4 “Main parts of the machine”, for a description of
the machine's operating controls. Figs. 4 and 6. Figs. 4 and 6

1.5 Nameplates

Nameplate on the machine



Name and address of the manufacturer.



Mark showing type of machine.



Total weight of the machine: TR 1,780kg, SM 1,850kg.



Diameter of the crosscut saw-blade 1000 mm, the hole 40 mm.



The highest permitted rotational speed is 1000 r.p.m



Hydraulics, max. 210 bar



Serial number and year of manufacture.

The nameplate is located at the infeed deck end of the machine.

Nameplates on the electric drive



-phase motor



Voltage 230/380 V or 380/600 V, may vary depending on the country.



Output 15 kW.



Current 35 A.

Summary of Contents for Power 100S






































Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands

Palax Power 100S, Operating Instructions Manual

Search results

Summary of Contents for Power 100S

Reviews:

Related manuals for Power 100S

Brands by name

Popular brands