Palax C750 Ergo Instruction Manual Download Page 9

Page: 9 / 34

Palax C750

Translation

1-2018

1.5

Nameplates

Nameplate on the machine

Name and address of the manufacturer.

Mark showing type of machine.

Total weight of the machine.

Diameter of the crosscut saw-blade 750 mm, the hole 35 mm.

The highest permitted rotational speed 1500 r.p.m

Max. hydraulic pressure 200 bar.

Serial number and year of manufacture.

Nameplate at the rear of the blade housing

Nameplates on the electric drive

3-phase motor.

Voltage 230/380 V or 380/600 V, may vary depending on the country.

Output 10,4 kW.

1.6

The main dimensions and models of the machine

Machine model

PALAX C750 Ergo

PALAX C750 Pro, Pro+

DRIVING POWER

TR/SM

Weight

810 kg

900 kg

840 kg

930kg

12,6 kW; fuse size: minimum 25A

Height/width/length

Transport position 2.45m / 1.3m / 2.8m

In-feed conveyor

Length 2.4m Height 0.9 m

Diameter of blade/hole

750mm/ 35mm

Max. rotation speed of blade 1500 r.p.m.

Max. diameter of the log

Max. cutting diameter of the log 30 cm

Max./min. length of the log

The maximum length of log that can be split is 55 cm.

The 4.3 m firewood conveyor is included in the weight.

1.7

Safety instructions

General regulations and restrictions

The maximum length of the log to be cut is 4 metres. Danger of turning over! If no log-
stand or log-deck is used.

The machine is exclusively intended for the production of firewood.

The machine may only be operated by one person.

The machine must be equipped with lights for transportation on public roads.

When transporting the machine on public roads hitched to the three-point linkage of a
tractor, the maximum allowed driving speed is 25 km/h.

The danger zone around the conveyor is 5 metres to the sides and to the rear.

Lift and lock the infeed deck and the discharge conveyor in the transport position for
transportation.

The three-point linkage of the tractor is of size-category two. If using a tractor larger in
size, check that there is sufficiently space for the PTO shaft and its protective guard.

Only persons over 18 years of age are allowed to operate this machine.

Summary of Contents for C750 Ergo



































Search results

Summary of Contents for C750 Ergo

Reviews:

Related manuals for C750 Ergo

Brands by name

Popular brands

Palax C750 Ergo, Instruction Manual

Search results

Summary of Contents for C750 Ergo

Reviews:

Related manuals for C750 Ergo

Brands by name

Popular brands