background image

1.  The  winch  should  be  mounted  with  the  centerline 

of  the  drum  in  a  horizontal  position.  The  mounting 
plane  of  the  base  may  be  rotated  in  any  position 
around this centerline.

2.  Because  of  the  design  of  the  mounting  base,  the 

direction of line pull should only be as shown in the 
above  illustration.  Line  pulls  in  any  other  direction 
must be approved by BRADEN Engineering.

3.  When  mounting  the  winch,  use  all  four  (4)  mount-

ing holes and grade 5 (8.8) or better bolts and nuts. 
Tighten to recommended torque.

 

     It is important that the winch is mounted on a surface 

that will not flex when the winch is in use, and cause 
binding of the gear train. Binding in the gear train will 
result  in  accelerated  wear  and  heat.  Also,  be  sure 
the winch is mounted on a flat surface. If necessary, 
use shim stock to insure the mounting surface is flat 
within 0.020 inch (0.5 mm).

4.  The  vent  plug  must  always  be  located  above  the 

horizontal  centerline.  If  the  winch  is  mounted  on  a 
pivoting  surface,  be  sure  vent  plug  remains  above 
the centerline in all positions. If necessary, reposition 
bearing support and vent plug as follows:

 

A. Remove bearing support bolts.

 

B. Rotate bearing support until vent plug is  
  positioned correctly and bolt holes are  
  aligned.

 

C. Evenly tighten bolts to recommended  
  torque.

5.  Hydraulic  lines  and  components  that  operate  the 

winch should be of sufficient size to assure minimum 
back pressure at the winch. The motor manufacturer 
recommends  that  the  back  pressure  not  to  exceed 
100 PSI (690 kPa) for optimum motor seal life. 150 
PSI  (1,030  kPa)  is  the  maximum  allowable  back 
pressure.  The  standard  winch  is  supplied  with  the 
motor internally drained. If high back pressures are 
encountered,  the  motor  may  be  externally  drained 
directly to tank to improve motor seal life. For back 
pressures  exceeding  150  PSI  (1,030  kPa)  consult 
BRADEN Service Department.

6.  The  winch  should  be  mounted  perpendicular  to  an 

imaginary line from the center of the drum to the first 
sheave  to  insure  even  spooling.  Make  certain  the 
fleet angle does not exceed 1-1/2 degrees.

WINCH INSTALLATION

VENT PLUG
ABOVE CENTERLINE

CL

6

6.75 in.
(171 mm)

13.5 in.
(343 mm)

11.625 in.
(295 mm)

5.813 in.
(148 mm)

4 THRU HOLES
0.656 in. (17 mm)

CL

DRUM

240o

30o

30o

Summary of Contents for BRADEN/GEARMATIC BG8A

































Reviews: