background image

1.8.3.  See CERTIFICATE of CONFORMITY 

section for Outdoor Noise declaration of 
conformity. 

1.9. 

Machine specific safety. 

1.9.1.  NEVER direct the outlet of the 

pressure washer jet towards anyone, which 

includes adults, children, all pets and livestock 
or other objects that can be damaged. 
1.9.2.  You MUST know how to STOP the 

machine quickly. You MUST also know how to 
safely bleed the built up pressure. 
1.9.3.  To reduce the risk of injury, close 

supervision is necessary when a product is 
used near children. 
1.9.4.  You MUST be thoroughly familiar with 
the controls. 
1.9.5.  Stay alert – watch what you are doing. 
1.9.6.  DO NOT operate the product when 

fatigued or under the influence of alcohol or 
drugs. 
1.9.7.  Keep operating area clear of all 

persons not involved in the pressure washing 
process. 
1.9.8.  DO NOT overreach or stand on 

unstable support. You MUST maintain good 

footing and balance at all times. Be careful 

that you do not slip on any water residue. You 

MUST keep working surface free of excess 
water 
1.9.9.  Follow the maintenance instructions 
specified in the manual. 
1.9.10.  DO NOT leave the pump running for 

longer than 1 minute without using the pump 

will overheat. Damaged caused in this way will 
invalidate any warranty. 
1.9.11.  DO NOT let the unit freeze. You MUST 

always empty the machine of all water after 

use and before storage – this is especially 

important in very cold weather or at times 

when the weather gets down to freezing 
temperatures. 
1.9.12.  Only operate the machine outdoors. 
1.9.13.  NEVER use the pressure washer to 

spray dangerous liquids such as petrol, acids 
etc.  
1.9.14.  The exhaust will be HOT during and 

shortly after use – You MUST keep all body 

parts and flammable materials clear of the 
exhaust at all times. 
1.9.15.  NEVER under any circumstance 

attempt to repair the high pressure hose. You 

MUST instead replace any damaged hose or 
other high pressure components. 
1.9.16.  Under NO circumstances should you 

modify or alter the Pressure Washer in any 

way. Modifications can create serious safety 
hazards and will also void the warranty. 

Page 6

First edition - 

April

 201

7

Summary of Contents for P72800A

































Reviews: