background image

2.  BATTERY & CHARGING

Charging your lithium ion battery

The tools battery has been shipped in a low charge condition, and 

requires charging prior to use. Allow several cycles of charging and 

discharging (through use of the tool) for the battery to reach its optimum 

performance / runtime.

CAUTION:

 

THE CHARGER FOR THIS PRODUCT SHOULD 

BE PROTECTED BY A RESIDUAL CURRENT DEVICE 

(RATED AT 30MA OR LESS).

1    Connect the charger into a mains power outlet.

4  The charger LED will 

illuminate red signifying that 

the battery is charging.

3   With the charger sitting on a 

flat surface, align the raised 

ribs on the battery with 

the recess in the charger 

and slide onto the charger 

ensuring a firm connection.

2   The charger LED will flash 

green showing power 

is being supplied to the 

charger.

5  The charger LED will 

illuminate green once the 

battery is fully charged.

Battery Charge Indicator

The purchased battery is equipped 

with a battery charge indicator to 

show the state of the battery charge.
Press the charge indicator button and 

look to see which LED lights.

Battery requires immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note:

 The battery needs to be removed from the tool to check the state 

of charge. 

Battery protection system

The tool is equipped with the battery protection system, which helps to 

ensure a long service life.
The output power automatically cuts off during operation when the tool 

and/or battery are placed under the following situations: 

•   When the tool is overloaded:    

   If this occurs, release the trigger switch and remove causes of 

overload, then pull the switch trigger again to restart. 

•   When the remaining battery capacity becomes low: 

  Recharge the battery pack.

Note:

  The battery protection system does not in any way damage the 

tool.

Note:

 

 The indicated capacity may be lower than the actual level during 

use or immediately after using the tool.

Note:

 

 Always use 2 batteries of same capacity and same charge state 

with the mower

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Flashing)

Battery is charging (low charge)

RED (Illuminated)

Battery is charging (mid charge)

GREEN (Illuminated)

Battery is fully charged

BOTH(Illuminated)

Battery pack is too hot or too cold (charging 

will begin automatically when battery reaches 

correct charging temperature).

BOTH (Flashing)

Defective battery. Never charge a defective 

battery pack!
Remove battery pack from charger.

Summary of Contents for PXCLMK-018










Reviews: