background image

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed  for a period  of 

36  months from the original date of purchase 

and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in 
accordance with the terms of this warranty. Warranty excludes consumable parts, for example: 
head assembly, feed wheel handles, keyed chuck, allen key, chuck key, steel column, table, 
belt, base, column support bolts.

WARNING

The following actions will result in the warranty being void.

Professional, Industrial or high frequency use.

If the tool has been operated on a supply voltage other than that specified on the tool.

If the tool shows signs of damage or defects caused by or resulting from abuse, accidents 
or alterations.

Failure to perform maintenance as set out within the instruction manual.

If the tool is disassembled or tampered with in any way.

OZITO

Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175

OW5

WARRANTY

YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER 

TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO 

YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.

PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR 

CUSTOMER SERVICE HELPLINE:

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF 

PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL 
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY 

OR PROCEDURE.

The benefits provided under this warranty are in addition to other rights and remedies which 
are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to a 
replacement or refund for a major failure and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if 
the goods fail to be of acceptable quality and the failure does not amount to a major failure. 

Generally you will be responsible for all costs associated with a claim under this warranty, 
however, where you have suffered any additional direct loss as a result of a defective product 
you may be able to claim such expenses by contacting our customer service helpline above.

`

Australia 1800 069 486

New Zealand 0508 069 486

Summary of Contents for DP-350

















Reviews: