background image

07/08

Instructions

Safety Guidelines

4

 

USAGE

  4

4

 

Whe correctly

 

fitted to the 

 

base the indicator

   

shows

 GREEN, to

 

release push until red

NOTE: This child  seat must be installed rearward 

facing.

1.Installation:

 Lower the infant carrier onto the ISOFIX base 

aligning the two bars on the infant carrier base with the 

corresponding attachments on the base. Push down until you 
year the click and the indicator shows GREEN.

 Pull up on 

the infant carrier handle to check it is securely fitted.

2.

 To remove

:

  

Push the seat locking button

 until the 

indicator shows red then lift the infant carrier up and 

away from the base.

4.8 

Fitting the infant carrier (car seat) to the 

 ISOFIX ba

se

4.9.2

 Fitting and removing the sun shade

IMPORTANT:

 The sun shade can only be effective if the handle is in the upright position.

Installation:1. Put the sunroof cover into the gap between the shell and outside cover. 2. Put the rope of sunroof onto the hook 

of both sides on the outside cover.3.Hook the top sunroof onto the hooks of the handle.

The ISOFIX attachments can be adjusted to other positions to fit the different positions of ISOFIX anchorage points relative ti the vehicle 
seat. As the picture above shows (picture 1) pill up the ISOFIX adjusting lever found at the front of the base and the ISOFIX bars on eithe 
side of the base will eject to the longest position. Connect both of the ISOFIX attachments with the corresponding ISOFIX vehicle 
anchorage points. When you hear the 'clicks' the ISOFIX bars should be attached to the vehicle anchors. Check the ISOFIX status 
windows, the windows will show GREEN when correctly fitted ( 

4.7,

picture 2). To release the ISOFIX attachments

 bars

; push the the 

release button/slider (

4.7

 

picture 2). To complete the installation of the base; lift up the front lever (ISOFIX adjusting button, 

4.7 

picture 1) 

and push the base towards the vehicle seat back until is is pressed firmly against the vehicle seat backrest.
Installation of the ISOFIX base is now complete. Check once again the status windows are showing GREEN.
IMPORTANT: Except the first position (the position where the bars are fully extended), the ISOFIX adjusting button need not be lifted, the 
seat base can be simply pushed back towards the the vehicle seat back

USAGE

USAGE

Summary of Contents for Capsule Infant









Reviews: