Oxgard CUBE C-03 Installation Manual Download Page 2

Page: 2 / 36

VZR.247800.001

Turnstile CUBE C-03

Installation Manual

CONTENTS

General Provisions ......................................................................................................................... 4

Safety precautions .......................................................................................................................... 5

Preparing the product for installation ........................................................................................... 6

3.1 Procedure for transporting the product to the installation site ................................................. 6

3.2 Rules for unpacking the product ............................................................................................. 6

3.3 Rules for visual inspection of the product ............................................................................... 6

3.4 Product installation site requirements ..................................................................................... 8

3.5 Procedure for checking compliance of the installation place ................................................... 9

Installation and dismantling of the product ................................................................................ 10

4.1 Equipment required .............................................................................................................. 10

4.2 Installing the product ............................................................................................................ 10

4.3 Dismantling the product ........................................................................................................ 14

Connecting and setting the product ............................................................................................ 15

5.1 Power connection ................................................................................................................. 18

5.2 Connecting the control panel ................................................................................................ 20

5.3 Connecting the access control system (optional) .................................................................. 21

5.4 Connecting the control panel to the ACS controller .............................................................. 26

Comprehensive inspection .......................................................................................................... 29

6.1 Visual inspection and verification of the product readiness for use ....................................... 29

Acceptance of the installed product ............................................................................................ 30

APPENDIX A

— Brief description of CAN2.0 data bus ...................................................................... 31

APPENDIX B

— Position of mounting holes relative to the external dimensions of the turnstile . 32

APPENDIX C

— Turnstile connection diagram .................................................................................. 33

Summary of Contents for CUBE C-03





































Search results

Summary of Contents for CUBE C-03

Reviews:

Brands by name

Popular brands

Oxgard CUBE C-03, Installation Manual

Search results

Summary of Contents for CUBE C-03

Reviews:

Brands by name

Popular brands