manualshive.com logo in svg

oxford diffraction KMW3000C, User Manual

Share
Download
oxford diffraction KMW3000C User Manual Download Page 15

INSTALLATION AND SETTING TO WORK 

KMW3000C

 

 

Version 1

 

USER MANUAL 

KMW3000CChiller v1.1.doc

 Page 

11

 

5.2 Installation and Setting to Work 

5.2.1 Preparation of Site and Services 

5.2.1.1 Environmental Requirements 

It is the customer’s responsibility to ensure that all local building and safety regulations are met. 

Ensure that the environmental conditions of the installation site conform to the requirements stated 
in the SPECIFICATIONS section of this manual. 

5.2.1.2 System Layout  

The minimum distance between the back or side of the casing, and other equipment must be 
greater than 30 cm. 

Do not place the KMW3000C close to any other heat-producing equipment. 

5.2.1.3 Electrical Services 

The electrical supply must conform to the requirements stated in the SPECIFICATIONS section of 
this manual. 

Locate the electricity supply close to the system and provide: 
Phase  

L 

Neutral  

N 

Protection PE 

The mains plug should be readily reachable by the operator when the equipment has been 
installed. 

5.2.1.4 Water Supply 

Prepare 30 litres of clean, filtered tap water to fill the reservoir. 

5.2.2 Setting to Work 

The location of connectors on the KMW3000C is shown in figure 5.2.1. 

 

 

 

 

 

 

 

Summary of Contents for KMW3000C


























Reviews:

No comments

Brands by name

Popular brands

Load more brands