manualshive.com logo in svg

OVS LTN8608-P8, Quick Start Manual, Page: 92 / 231

Share
Download
OVS LTN8608-P8 Quick Start Manual Download Page 92

User Manual of Network Video Recorder   

63 

5.1

 

Configuring Parameters 

Purpose:   

By configuring the parameters you can define the parameters which affect the image quality, such as the 

transmission stream type, the resolution and so on. 

Before you start:

 

1.

 

Make  sure  that  the  HDD  has  already  been  installed.  If  not,  please  install  a  HDD  and  initialize  it. 

(Menu>HDD>General) 

 

Figure 5. 1

 

HDD- General 

 

2.

 

Check the storage mode of the HDD 

1)

 

Click 

Advanced

 to check the storage mode of the HDD.   

2)

 

If the HDD mode is 

Quota

, please set the maximum record capacity and maximum picture capacity. 

For detailed information, see 

Chapter

 

Configuring Quota Mode.

 

3)

 

If  the  HDD  mode  is 

Group

,  you  should  set  the  HDD  group.  For  detailed  information,  see 

Chapter 

Configuring HDD Group for Recording and Capture.

 

 

Figure 5. 2

 

HDD- Advanced 

 

Steps

: 

1.

 

Enter the Record settings interface to configure the recording parameters: 

Menu > Record > Parameters 

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Reviews:

No comments