manualshive.com logo in svg

OVS LTN8608-P8, Quick Start Manual, Page: 13 / 231

Share
Download
OVS LTN8608-P8 Quick Start Manual Download Page 13

Network Video Recorder Quick Start Guide 

12 

Chapter 2 

 

Installation and Connections 

2.1

 

NVR Installation 

During installation of the NVR: 

1.

 

Use brackets for rack mounting. 

2.

 

Ensure ample room for audio and video cables. 

3.

 

When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. 

4.

 

Connect the alarm cable. 

5.

 

Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. 

6.

 

Ensure the NVR is grounded. 

7.

 

Environmental temperature should be within the range of -10

 

ºC ~ 55

 

ºC, 14ºF ~ 131ºF. 

8.

 

Environmental humidity should be within the range of 10% ~ 90%. 

2.2

 

Hard Disk Installation 

Before you start: 

Disconnect the power from the NVR before installing a hard disk drive (HDD). A factory recommended HDD 

should be used for this installation. Up to eight SATA hard disks can be installed. 

Tools Required: 

Screwdriver. 

Steps: 

1.

 

Remove the NVR cover by unfastening the screws on the back and side.   

 

Figure 2. 1

 

Remove the Cover     

 

2.

 

Connect one end of the data cable to the motherboard of NVR and the other end to 

the HDD.   

 

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Reviews:

No comments