manualshive.com logo in svg

OVS LTN8608-P8, Quick Start Manual, Page: 190 / 231

Share
Download
OVS LTN8608-P8 Quick Start Manual Download Page 190

User Manual of Network Video Recorder   

161 

12.7

 

Checking HDD Status

 

Purpose: 

You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case 

of HDD failure.

 

Checking HDD Status in HDD Information Interface 

Steps: 

1.

 

Enter the HDD Information interface. 

Menu > HDD>General 

2.

 

Check the status of each HDD which is displayed on the list, as shown in Figure 12. 25. 

 

Figure 12. 25

 

View HDD Status (1) 

 

 

If the status of HDD is 

Normal 

or 

Sleeping

, it works normally. If the status is 

Uninitialized 

or 

Abnormal

, please 

initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one. 

Checking HDD Status in HDD Information Interface 

Steps: 

1.

 

Enter the System Information interface. 

Menu >Maintenance > System Info   

2.

 

Click the 

HDD

 tab to view the status of each HDD displayed on the list, as shown in Figure 12. 26. 

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Reviews:

No comments