manualshive.com logo in svg

OVS LTN8608-P8, Quick Start Manual, Page: 159 / 231

Share
Download
OVS LTN8608-P8 Quick Start Manual Download Page 159

User Manual of Network Video Recorder   

130 

 

Figure 11. 2

 

Net Fault-tolerance Working Mode 

 

 

11.2

 

Configuring Advanced Settings 

11.2.1

 

Configuring PPPoE Settings 

Purpose: 

Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). 

Steps: 

1.

 

Enter the 

Network Settings 

interface. 

Menu >Configuration> Network 

2.

 

Select the 

PPPoE 

tab to enter the PPPoE Settings interface, as shown in Figure 11. 3. 

 

Figure 11. 3

 

PPPoE Settings Interface 

 

3.

 

Check the 

PPPoE 

checkbox to enable this feature. 

4.

 

Enter 

User Name

, and 

Password 

for PPPoE access. 

 

The User Name and Password should be assigned by your ISP. 

5.

 

Click the 

Apply

 button to save and exit the interface.   

6.

 

After successful settings, the system asks you to reboot the device to enable the new settings, and the 

PPPoE dial-up is automatically connected after reboot. 

You can go to Menu >Maintenance>System Info >Network interface to view the status of PPPoE connection. 

Please refer to 

Chapter Viewing System Information

 for PPPoE status. 

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Reviews:

No comments