OVS LTN8608-P8 Quick Start Manual Download Page 132

Page: 132 / 231

User Manual of Network Video Recorder

103

Figure 7. 8

Export Finished

The backup of video files using USB writer or SATA writer has the same operating instructions. Please

refer to steps described above.

7.1.3

Backing up by Event Search

Purpose:

Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or

eSATA HDD. Quick Backup and Normal Backup are supported.

Steps:

Enter Export interface.

Menu>Export>Event

Select the cameras to search.

Select the event type to alarm input, motion or VCA.

Figure 7. 9

Event Search for Backup

Set search condition and click

Search

button to enter the search result interface. The matched video files

are displayed in Chart or List display mode.

Select video files from the Chart or List interface to export.

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Search results

Summary of Contents for LTN8608-P8

Reviews:

OVS LTN8608-P8, Quick Start Manual, Page: 132 / 231

Search results

Summary of Contents for LTN8608-P8

Reviews: