manualshive.com logo in svg

OVS LTN8608-P8, Quick Start Manual, Page: 33 / 231

Share
Download
OVS LTN8608-P8 Quick Start Manual Download Page 33

User Manual of Network Video Recorder   

4 

Preventive and Cautionary Tips

 

Before connecting and operating your device, please be advised of the following tips: 

•

 

Ensure unit is installed in a well-ventilated, dust-free environment. 

•

 

Unit is designed for indoor use only. 

•

 

Keep all liquids away from the device. 

•

 

Ensure environmental conditions meet factory specifications. 

•

 

Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it 

may cause damage to the sensitive electronics within the unit. 

•

 

Use the device in conjunction with an UPS if possible. 

•

 

Power down the unit before connecting and disconnecting accessories and peripherals. 

•

 

A factory recommended HDD should be used for this device. 

•

 

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or 

equivalent type only. Dispose of used batteries according to the instructions provided by the battery 

manufacturer.   

   

 

   

 

User Manual

Summary of Contents for LTN8608-P8








































































































































































































































Reviews:

No comments