background image

Copyright and Disclaimer 

 
 
 
 
 
 

AirLive POE-FSH8PW User’s Manual 

 

ii

FCC Statement 

 
Federal Communication Commission Interference Statement This equipment has been 
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one of the 
following measures: 

z

  Reorient or relocate the receiving antenna. 

z

  Increase the separation between the equipment and receiver. 

z

  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

z

  Consult the dealer or an experienced radio/TV technician for help. 

 
FCC Caution 

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. For product available in the USA/Canada market, only channel 1~11 can be 
operated. Selection of other channels is not possible. 
This device and its antenna(s) must not be co-located or operation in conjunction with any 
other antenna or transmitter. 

 
IMPORTANT NOTE 

FCC Radiation Exposure Statement: 
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with minimum distance 
20cm between the radiator & your body.

 

 
 

 

Summary of Contents for Air Live POE-FSH8PW























































Reviews: