Ovislink Air Live N.Power Page 77 User Manual Download

Page: 77 / 108

7. Client Mode

AirLive N.Power User’s Manual

You can now select the SSID you want to connect with, and then press the “Connect”

button. If encryption key is required, the AP will prompt you to enter the encryption

information.

7.2.4 Advance Settings

BG Protection:

The 802.11g standard includes a protection mechanism to ensure

mixed 802.11b and 802.11g operation. If there is no such kind of mechanism exists,

the two kinds of standards may mutually interfere and decrease network’s

performance.

AckTimeOut:

When a packet is sent out from one wireless station to the other, it will

wait for an Acknowledgement frame from the remote station. The station will only

wait for a certain amount of time; this time is called the ACK timeout.

In most

conditions, please do not change the Tx and Rx Acktimeout value. The N.Power’s
default value is correct in most cases.

Tx Burst:

These are the scheme used for improving the performance of the data

transmission in 11n and Turbo modes. It is recommended to keep the settings on.

Summary of Contents for Air Live N.Power













































































































Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands

Ovislink Air Live N.Power, User Manual

Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands