Ovislink Air Live N.Power Page 43 User Manual Download

Page: 43 / 108

4. Configuration: Router Mode

AirLive N.Power User’s Manual

Procedure to make encryption

Step1

Select your SSID:

If you have enabled the “Multiple SSID” function, there will

be more than one SSID to choose from. Each SSID (Virtual AP) can have its own

security policy.

Step2

Select Security Policy

: N.Power offers a full suite of security policy including

WEP(Pre-Shared Key), WPA(certificate), WPA-PSK(AES), WPA2-PSK(AES), and

802.1x Radius Authentication. Recently WiFi regulation prevents the use of TKIP

encryption in 11n mode. Therefore, the TKIP is only available in 11b/g mode.

highly recommend using WPA2-PSK AES Encryption as the easiest and much
secured scheme for encryption.

4.4.5 Access Control

Wireless Settings -> Access Control

The N.Power allows you to define a list of MAC addresses that are allowed or denied to

access the wireless network. This function is available only for Access Point and AP

Router modes. This function is available only for Access Point and Gateway modes.

Summary of Contents for Air Live N.Power













































































































Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands

Ovislink Air Live N.Power, User Manual

Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands