Ovislink Air Live N.Power Page 59 User Manual Download

Page: 59 / 108

5. System Configuration and Status Menu

AirLive N.Power User’s Manual

5.7 Configuration Save and Restore

System Configuration -> Configuration Save and Restore

The N.Power can save and restore the settings to a file.

You can save system configuration settings to a file, and later download it back to the

N.Power

Export Settings:

Export the configuration file to your PC so you can restore the

settings later.

Import Settings file location:

Please browse for the configuration file location for

restoration of settings

5.8 Factory Default

System Configuration -> Factory Default

You can reset the configuration of your N.Power to the factory default settings.

5.9 Status Menu

5.9.1 Device Information

From this menu, you can know the Firmware version, System Up time, IP and MAC

addresses, and check whether the USB Storage is connected.

Summary of Contents for Air Live N.Power













































































































Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands

Ovislink Air Live N.Power, User Manual

Search results

Summary of Contents for Air Live N.Power

Reviews:

Related manuals for Air Live N.Power

Brands by name

Popular brands