Overlander TS80 Manual Download Page 2

Page: 2 / 20

1. Specifications

..................................................................................

2. Features

..........................................................................................

3. Unit Exterior

...................................................................................

4. Warnings and Safety Notes

............................................................

5. Program Flow Chart

........................................................................

6. Parameter Set Up

...........................................................................

7. Lithium Battery Program

................................................................

7.1. Lithium Battery Charging......................................................... 8

7.2. Lithium Battery Storage Control............................................

7.3. Lithium Battery Discharging..................................................... 10

8. NiMH/NiCd Battery Program

.........................................................

8.1. NiMH/NiCd Battery Charging................................................... 11

8.2. NiMH/NiCd Battery Discharging............................................... 12

8.3. NiMH/NiCd Battery Cyclic Charge/Discharge........................... 12

9. Pb Battery Program

........................................................................

9.1. Pb Battery Charging................................................................. 14

9.2. Pb Battery Discharging............................................................. 15

10. Digital Power Supply Program

.......................................................

11. Check Status

...................................................................................

12. Warnings and Error Messages

........................................................

13. Warrant and Services

.....................................................................

Contents

Summary of Contents for TS80





















Search results

Summary of Contents for TS80

Reviews:

Related manuals for TS80

Brands by name

Popular brands

Overlander TS80, Manual

Search results

Summary of Contents for TS80

Reviews:

Related manuals for TS80

Brands by name

Popular brands