manualshive.com logo in svg

Overland Tandberg NEOxl 80, Replacement Instructions Manual

Share
Download
Overland Tandberg NEOxl 80 Replacement Instructions Manual Download Page 5

NEOxl 80 Spare Chassis Replacement Instructions

10400904

©2019 Overland-Tandberg

Page 5 of 8

  

Swap Components

Move Covers

IMPORTANT:  When replacing an module in either the top or 
bottom position, you must move the cover from the old module 
to the new one.

If necessary, move a 

top

 cover:

1.

At the old module, insert a small flathead screwdriver or 
Torx screwdriver into the front hole (1) to retract the 

spring lock

, slide the 

cover

 forward (2) until it reaches 

the tool, remove the tool, and then continue sliding the 
cover to the front of the module until all the tabs are 
released.

2.

Remove the 

cover

 (3) from the existing module.

3.

At the new module, install the 

cover

.

Align all cover tabs with the slots, gently push it down, 
and then slide the cover towards the rear until the spring 
lock engages.

If necessary, move a 

bottom

 cover:

1.

Gently turn both modules 

upside-down

.

2.

At the old module, insert a small flathead screwdriver or 
Torx screwdriver into the front hole (1) to retract the 

spring lock

, slide the 

cover

 forward (2) until it reaches 

the tool, remove the tool, and then continue sliding the 
cover to the front of the module until all the tabs are 
released.

3.

Remove the 

cover

 (3) from the existing module.

4.

At the new module, install the 

cover

.

Align all cover tabs with the slots, gently push it down, 
and then slide the cover towards the rear until the spring 
lock engages.

5.

Gently turn both modules 

back over

.

Move Power Supplies

1.

At the old module, loosen the 

three blue thumbscrews

 

on the power supply.

2.

Using the thumbscrews, slowly pull the 

power supply

 

approximately 4 inches (10 cm) out of the library.

3.

While supporting the bottom of the power supply with one 
hand, use the other hand to completely 

remove

 the 

power supply

 from the module.

4.

At the new module, position the 

power supply

 onto the 

alignment rails.

5.

Slide the 

power supply

 into the library until it is flush 

with the rear panel of the library.

6.

Finger-tighten the 

three blue thumbscrews

 to secure 

the power supply to the library.

7.

Repeat 

Steps 1–6

 to remove any other 

power supply

.

Summary of Contents for NEOxl 80









Reviews:

No comments

Brands by name

Popular brands

Load more brands