background image

51

082809

System Assembly

Installing OVSOL System 5-24-SCE

Model Number 540 00 17K-SCE

Solar Closed-Loop Domestic Hot Water System

Oventrop Components

OVSOL 5 -16 and 5-8 Evacuated Tube Collector . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 filled weight: 337 lbs.

Regusol 130 EL Solar Transmission Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 filled weight:   20 lbs. 

119 Gallon OVSOL glass lined Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   

 filled weight: 1315 lbs.

Regusol Fill and Flush Valve

Oventrop NT Propelyne Glycol Antifreeze

System Design Description

 

The solar closed-loop heating system consists of the Oventrop Regusol 130 EL  pump and control station, 

one OV-5 evacuated tube collector, and an 80 gallon glass lined tank with one internal coil and an electric backup 

element. An expansion tank is installed at the Regusol on the safety group. Oventrop NT propelyne glycol antifreeze 

is filled into the closed loop system through the Regusol fill and flush valve.

 

Cold water is piped to the solar tank. An anti-scald valve must be installed for hot water mixing to hot water 

fixtures if the solar tank high limit in the Regusol controller is set above 120 

o

F.

OVSOL System 5-24-SCE

 / 119 gallon, Evacuated tube, Single coil electric tank

Summary of Contents for ovsol














































































Reviews: