manualshive.com logo in svg

Oval Ultra Oval LW76E, Instructions Manual

Share
Download
Oval Ultra Oval LW76E Instructions Manual Download Page 36

B-320-2-E

36

(3)  Pull  the  battery  pack 

o u t  o f  t h e  i n t e r n a l 
assembly  (the  battery 
pack  is  coupled  to  the 
internal  assembly  with 
connectors).

(4)  Install a new battery pack in reverse order of removal.

10. ABOUT THE BATTERY PACK

The register operates on a built-in battery. Take the 
following precautions.

 CAUTION

1.  The  battery  pack  is  of  dedicated  one.  Do 

not  attempt  to  use  commercially  available 
batteries of other type.

2.  The  battery  pack  is  of  one-piece  molding. 

Never  give  impact  shock  or  disassemble.  Or 
loss of performance may possibly result.

3.  For storage, keep moisture and dust out.

Battery  packs  are  available  at  your  nearest  OVAL 
sales representative or at OVAL Service Center.

BATTERY PACK

10.1 Battery Life
This battery is good for about 4 years.

The  life  expectancy  is  based  on  an  8-hours-a-day 
operation  basis  but  may  vary  with  operating  and 
environmental conditions.
When the battery is beginning to run down, an alarm 
"BATT" blinks in the display. As this state advances, 
a warning "ALM" comes on, closing the shutoff valve 
automatically if a batch process is in progress (shutoff 
valve is open) and saving variables of the total count 
and cumulative total in the memory.

As  a  rule  of  thumb,  it  takes  about  8  days  from 
"BATT"  to  begin  blinking  until  "ALM"  to  come  on. 
Good practice is to replace the battery in this period.

10.2 Battery Pack Replacement

Battery pack replacement procedure is given below.

NOTE:  For safety's sake, do not fail to make sure that the shutoff valve remains closed before you start 

working. If it is in the open position (metering), close the shutoff valve to prevent erratic operation 
following the replacement.

(1)  Take steps (3) through (7) of Sec. 9.2 "Register Disassembly".
(2)  Take off 5 screws securing the battery pack in place.

BATTERY PACK

FITTING SCREW

INTERNAL ASSEMBLY

CN2-2

CN2-1

CN1

 CAUTION: 

Use care to avoid a distorted or out-of-position connector while installing the battery 
pack in the internal assembly.

RUN

OUT

ALM

COUNT

END

X

L

BATT

DISPLAY

"BATT" BLINKS.

LIGHTS LIP.

LIGHTS UP.

Summary of Contents for Ultra Oval LW76E

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands