Oval ALTI mass CA001 Instructions Manual Download Page 63

Page: 63 / 162

L--740--28--E

7.10.2 Separately mounted sensor unit and transmitter wiring

Fig.7.9

Cut off shield wires here except for the

shield wire over BRN and RED lines.

Interconnect cable

Transmitter terminal box

Sensor terminal box

Shield

(Protected by black tube)

Shield
(Protected by black tube)

cut

Barrier cover to be applied

in a hazardous area

Brown

Red

Green

White

Blue

Grey

Purple

Yellow

Orange

Brown

Red

Green

White

Blue

Grey

Purple

Yellow

Orange

Interconnect cable (Max. 200m)

Sensor terminal box

シールド

（黒色チューブで保護）

カット

茶

赤

緑

白

青

灰

紫

黄

橙

茶

赤

緑

白

青

灰

紫

黄

橙

Shield wires:Black

Transmitter

TypeU

：

200m max.

TypeS Stainless steel tube type

：

50m max.

TypeS Titanium tube type

：

100m max.

TypeB

：

5m max.

CA00A, CA001, CA004

and CA006 to CA080

(T2

T3 and T4) are not

required.

NOTE 1. Do not fail to use dedicated interconnect cable.

2. Shield wire preparation

(1) Transmitter end:

As shown in the above figure, bundle shield wires colored in brown/red, green/white,

blue/grey, purple/yellow/orange, twist them, and cover the wires with a black tube. Then

connect only one wire to the terminal box (black) taking care to avoid potential contact

with the housing or conductive parts.

(2) Sensor end:

As shown in the figure, cover the brown/red shield wire with a black tube and connect it

to the terminal box taking care to avoid potential contact with the housing or conductive

parts. Clip all shield wires except brown/red as shown in the above figure.

3. Recommended cable end treatment:

Use of a stick type crimp terminal is not necessary.

9mm

Summary of Contents for ALTI mass CA001



































































































































































Search results

Summary of Contents for ALTI mass CA001

Reviews:

Brands by name

Popular brands

Oval ALTI mass CA001, Instructions Manual

Search results

Summary of Contents for ALTI mass CA001

Reviews:

Brands by name

Popular brands