background image

52.

Attach 

Rear Wall Narrow

Trim 

(2 - 1/2” x 2 1/2” x 79”)

where wall panels come together
and leave a seam. Position trim
equally on wall seam and flush at
bottom of Bottom Skirting. Use
6 - 1 1/2” finishing nails per piece
to secure. Attach both 

Side Wall Narrow Trims 

(79”

long) where wall seams come 
together on sides. Once again,
position trim equally on wall
seam, flush at bottom of Bottom
Skirting. Use 6 - 1 1/2” finishing
nails per piece to secure.

53.

Attach 

Horizontal Gable Trim

( 4- 1/2” x 3 1/2” x 31 1/4”) to both sides of shed.
(2 per side).  Position over gable and wall seam.
Use 4 - 1 1/2” finishing nails to secure each
piece.

Horizontal Gable Trim

54.

Attach

Side Facia 

(angle cut on ends) to

end roof panel battens.  Line facia up to form a
peak and attach to battens with 4 - 1 1/2”
screws per piece. End of facia should be
aligned flush with end of rafter. See 

Step 55

for

detail. Gap where facia boards come together
at peak will covered in 

Step 57.

51.

Position Trim flush with Bottom Skirting. At the top, Narrow Trim sit flush with bottom of Soffit

while Wide Trim will ride up on and site on side of end rafter. When correctly aligned, attach with 
6 - 1 1/2” finishing nails per piece.  

Side Wall Narrow Trim

Rear Wall Narrow Trim

wide

trim

1-888-658-1658                        www.outdoorlivingtoday.com            [email protected]

Page 21

Summary of Contents for 9x6 Cabana



























Reviews: