Outdoor living today 8x8 Sunshed Garden Shed Assembly Manual Download Page 23 | Manualshive

Page: 23 / 29

background image

74.

Position Mid Ridge Cap on mid rafter.

72.

Attach remaining

Narrow Wall Trims

around the Sunshed. Narrow trims are used where wall

panels come together and leave a seam. Note, the Narrow Trim on the Short Wall side is only 79”
long. Attach with 6 - 1 1/2” finishing nails per piece. Align Trim so flush at bottom of bottom skirting.

73.

Locate all

Outside

and

Mid Ridge Caps

for Lexan Panels. Starting from the outside, position a

5 1/2” wide cap so outside edge is aligned with battens ends of roof and Cap end slides under roof.
When correctly aligned, attach Cap to center of outside rafter with 4 - finishing nails.

See Step 71.

Outside
Ridge Cap for
Lexan Panel

Mid Ridge
Caps for
Lexan

Straight
Edge

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 23

«
...
21
22
23
24
25
...
»

Summary of Contents for 8x8 Sunshed Garden Shed






























Reviews:

No comments

Related manuals for 8x8 Sunshed Garden Shed

Brand: IGMI Pages: 5

Brand: WATSON Pages: 12

Brand: Magres Baldai Pages: 2

Brand: feather&black Pages: 2

Brand: feather&black Pages: 3

Brand: feather & black Pages: 6

Brand: R&B Wire Products Pages: 2

Brand: Xavax Pages: 2

PROWANSJA S1D2S

Brand: GALA MEBLE Pages: 24

Brand: Rauch Pages: 26

Ameriwood Industries 3572207PCOM

Brand: Dorel Pages: 20

Brand: Furniture of America Pages: 5

TWO-POST ARCHED WOOD ARBOR

Brand: Forever Redwood Pages: 15

Brand: PBteen Pages: 3

Brand: Sango Pages: 11

Panacea Two-Sided Staircase

Brand: Direct Supply Pages: 2

Brand: Walker Edison Pages: 23

Brand: Quoizel Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands