manualshive.com logo in svg

Outdoor living today 8x8 Sunshed Garden Shed, Assembly Manual

Share
Download
Outdoor living today 8x8 Sunshed Garden Shed Assembly Manual Download Page 16

44. 

Complete installation for remaining Gussets

45.

Attach 

Simpson Strong Ties

to Top Wall

framing and plates and also to the underside of the
rafters. Use 4 - 1 1/4” screws to secure. There are
6 Ties to complete. Long Roof Side Ties are angled
at 22 1/2 degrees (long side to walls).

46.

Position 3/4” x 3/4” x 44” long 

Lexan Support Cleats

on each Long Rafter flush to end and

recessed 3/16” down from top of rafter. Nail to rafter using 6 - finishing nails. 

Note,

Start nails in

Supports on ground first. Complete remaining 7 Lexan Support Cleats. 

3/16” gap

47.

Identify all 

Roof Panels.

There are 2 Right and 2 left sided Roof Panels.  The outside of the panels

will have shingles overhanging the battens.  Starting on Short Roof Side, lift up and place a roof panel on
rafters so centered on mid rafter. Lowest batten on roof should be flush with end of rafter at bottom. Tack
down through shingles into rafter with 1 - 2.5” screws on bottom row of shingles. 

Shingles overhang battens to outside

Battens flush
with shingles

D. Roof Section

Toll Free 1-888-658-1658         www.outdoorlivingtoday.com          [email protected]

Page 16

batten
lines up
with end
of rafter.

Summary of Contents for 8x8 Sunshed Garden Shed






























Reviews:

No comments

Brands by name

Popular brands

Load more brands