Outdoor living today 8x15 Santa Rosa Assembly Manual Download Page 31 | Manualshive

Page: 31 / 34

background image

83.

Attaching the Gable Gusset is next, screw a 90 degree

Simpson Strong Tie up into 3rd and 5th batten of roof panel with
2-1 1/4” screws flush to end of batten. (see picture)

Place

Decorative Gusset Gable

underneath porch roof so peaks

line up. Lift up underneath Gusset Gable until seams meet. Mount
with 2- 1 1/4” screws into each Strong Tie.

81.

Place First Roof Ridge Cap on roof peak overhanging shingles by approximately 2”. Attach with

2- 1 1/2” Shingle Nails 9” from end. Place 2nd Ridge Cap 1” back from 1st cap. Attach with 2- 1 1/2”
Shingle Nails 9” from end. There are left/right Ridge Caps, alternate each Ridge Cap as you proceed.

82.

Place 3rd Ridge Cap 8” back from 2nd. (enough to cover shingle

nails). Attach 3rd Ridge Cap down as per

Step 81

. Continue to position

and attach Ridge Caps until half roof is complete. From opposite side,
position and attach Ridge Caps as described above. Score/cut 1 Ridge
Cap to 12” or to fit in the center of roof. Attach center cap with 4 - 1 1/2”
Shingle Nails.

9” from end

Alternate left/right Ridge Caps

8”

8”

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 31

Undercourse
Rid Cap

«
...
29
30
31
32
33
...
»

Summary of Contents for 8x15 Santa Rosa



































Reviews:

No comments

Related manuals for 8x15 Santa Rosa

Brand: ModuLaro Pages: 11

Bruges 2 FRF28-4138FSC

Brand: Palmako Pages: 53

Brand: Forest Pages: 6

Brand: Palmako Pages: 48

Brand: Solid Pages: 32

Brand: Solid Pages: 34

Palmako Claudia FR44-5540

Brand: Lemeks Pages: 55

PALMACO EL18-3422

Brand: Lemeks Pages: 58

Brand: Palmako Pages: 101

Brand: Palmako Pages: 101

Brand: Palmako Pages: 100

Brand: Palmako Pages: 48

Brand: Madeira Pages: 16

Brand: Palmako Pages: 64

Brand: Palmako Pages: 43

Cannes Summerhouse 10x6

Brand: Project Timber Pages: 18

Brand: Palmako Pages: 103

Palmako Roger FRE44-5953

Brand: Lemeks Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands