Outdoor living today 8x15 Santa Rosa Assembly Manual Download Page 3

Page: 3 / 34

Plywood Floor
Large (3)

Floor Joist
Frames
Large (3)

Floor Runners (15)

Plywood Floor
Small (3)

Exploded view of all parts necessary to complete
Floor Section. Identify all parts prior to starting.

Note, Floor Footprint is 182” deep x 96” wide.

Concrete Pad
(optional foundation method)

Floor Joist
Frames
Small (3)

5 1/2” Wide Deck
Boards (17)

Lay out

Large Floor Joist Frame and 2 Floor Joists

as illustrated above. Position Joists

equally in Floor Joist Frame. Use

Small Floor Joist Frame

as a template to determine joist position.

Position Joist so flush with framing.

Flush
with
framing

When correctly positioned, attach each Joist with 4 - 2 1/2” screws (2 per end). If door

location to be on left, position Small Floor Joist Frame to right. Reverse if opposite.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 3

A. Floor Section

Summary of Contents for 8x15 Santa Rosa



































Search results

Summary of Contents for 8x15 Santa Rosa

Reviews:

Related manuals for 8x15 Santa Rosa

Brands by name

Popular brands

Outdoor living today 8x15 Santa Rosa, Assembly Manual

Search results

Summary of Contents for 8x15 Santa Rosa

Reviews:

Related manuals for 8x15 Santa Rosa

Brands by name

Popular brands