Outdoor living today 8x12 SunShed Assembly Manual Download | Manualshive

Page: 33 / 34

background image

Completed
Potting Shelf
Setup.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 33

2.5” screws

Into Wall Stud

99.

Locate 1

Long Potting Shelf

and 2 Legs. Attach Legs in each front corner from the inside with 2 - 2.5”

screws. Attach Shelf framing to wall studs with 2 - 2.5” screws. Place 2nd Long Potting Shelf and 2 Legs
adjacent to Long Potting Shelf and attach together from underneath where end framings meet with 2 - 2.5”
screws. Attach Long Shelf into Wall Stud with 1 - 2.5” screw from underneath. Place Short Potting Bench in
corner and attach end framings together and also to wall studs with 4 - 2.5” screws. Attach 1 front center Leg.

100.

Locate 3rd Long Potting Shelf and 3 Legs. Attach Legs in front corners and outside rear

corner with 2 - 2.5” screws/leg from underneath. Place in rear corner against Short Potting Shelf and
attach together from underneath where framings meet with 2 - 2.5” screws. Attach Long Shelf into
Wall Stud with 1 - 2.5” screw from underneath.

«
...
31
32
33
34
»

Summary of Contents for 8x12 SunShed



































Reviews:

No comments

Related manuals for 8x12 SunShed

Brand: Palmako Pages: 55

Palmako Sally FR44-3838-1

Brand: Lemeks Pages: 54

Susanna FR44-5340

Brand: Palmako Pages: 106

Palmako Irene FRT44-5357-2

Brand: Lemeks Pages: 72

Brand: OLT Pages: 39

Brand: Palmako Pages: 56

Brand: Palmako Pages: 21

Brand: Palmako Pages: 46

Brand: Palmako Pages: 45

Brand: Palmako Pages: 55

Brand: Palmako Pages: 55

Brand: Palmako Pages: 56

Brand: Palmako Pages: 65

Brand: Sojag Pages: 30

Brand: Sojag Pages: 32

Brand: Sojag Pages: 56

Palmako Britta FRI40-4545

Brand: Lemeks Pages: 53

Palmaco EL18-4633-2

Brand: Lemeks Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands