Outdoor living today 8x12 SunShed Assembly Manual Download Page 26 | Manualshive

Page: 26 / 34

background image

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 26

76.

Place the Top Dutch Door Panel into place

and gap top and bottom panel 1/4” apart. Use a
shim once again to help you. Attach hinges to
trim with hinge hardware provided.

1/4” gap

bottom skirting

74.

Attach Door Hinges to

Top

and

Bottom Dutch Door

sections. Center Hinges should be positioned to edge of door
trim to prevent hinges from contacting each other while top and
bottom hinges may be centered on door trim. Use 2” & 3/4”
black screws on hinge / door attachment as shown above.

75.

Place Bottom Dutch Door panel into

position, gap 3/8” on bottom and evenly
spaced on sides and attach hinge to
doorway seam trim with 2” black screws.
Use shim to help keep the door evenly
spaced on bottom. One of the extra roof
shingles (see parts list) can be used.

Bottom Door

3/8” gap at
bottom.
Evenly
spaced on
sides.

3/4” screw

Doorway

Seam

T

rim

2” Black Screws

Top and Bottom Hinges
center on door trim.

Top Door Trim

Bottom Door Trim

Center Hinges

2“ Screws

Important

: Hinge not

exactly as shown.

77.

Attach

Door Handle, Exterior Barrel Bolt

and

Interior Barrel Bolt

to door. Handle is

positioned on top door, Barrel Bolt on bottom door and Interior Barrel Bolt (silver) to top door stud.
Attach Black Barrel Bolt as illustrated above with 3/4” Black Screws. Note how female part of Barrel
Bolt is positioned higher than male. Do a dry run first to position Barrel Bolt correctly.

Important

- Drill

pilot holes with 1/8” drill bit prior to securing with screws to prevent wood splitting.

Temporarily positioned
Interior Door Stop to help
align Interior Barrel Bolt.

«
...
24
25
26
27
28
...
»

Summary of Contents for 8x12 SunShed



































Reviews:

No comments

Related manuals for 8x12 SunShed

Brand: Palmako Pages: 55

Brand: habitat et jardin Pages: 31

Brand: G21 Pages: 44

Brand: finnhaus Pages: 68

Brand: G21 Pages: 40

PALMAKO FR44-5540-3

Brand: Lemeks Pages: 154

Brand: Palmako Pages: 62

Brand: Palmako Pages: 21

Brand: Gartenpro Pages: 36

Brand: Palmako Pages: 105

Brand: Palmako Pages: 19

Gardener's Shed GAR88-FJ-METAL

Brand: OLT Pages: 40

GS84-SLIDER-METAL-AK

Brand: OLT Pages: 38

SSGS1216-FJ-Ply

Brand: OLT Pages: 49

Brand: Palmako Pages: 102

MIKKEL EL16-1811

Brand: Palmako Pages: 67

FRAB19-4023FSC / 1059487

Brand: new garden Pages: 65

DURAMAX 10 Ft WoodSide

Brand: USP Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands