background image

60

61

6.8 Adjusting the side panels

Side panel with protection against cold, side panel with splash guard and protection against cold, carbon
side panel with splash guard

The side panels have to be fine-tuned when the drive wheel position is changed.
1)  Remove the drive wheel.
2)  Loosen the mounting screws on the side panel (see fig. 62, item 1).
3)  Attach the drive wheel to determine the position.
4)  Adjust  the  position  of  the  side  panel  (see  fig. 62,  item 2).  Adjust  the  height  so  the  top  edge  is  about 

25 mm

higher than the wheel surface to prevent pinching the fingers.

INFORMATION: Align the side panels downward.

5)  Tighten the mounting screws.
6)  Attach the drive wheel and check the freewheel.

After adjustment, the side panels have to be aligned the same on both sides.

62

“Plastic, plug-on” side panel 

The height of the forearm support can be best adjusted when the side panel is completely removed.
1) 

Height  adjustment  of  the  forearm  support:

  Use  a  ballpoint  pen  or  screwdriver  to  press  the  countersunk

locking button (see fig. 63, item 1). Move the forearm support to the desired position so the locking button re-
engages. Then fully insert the side panel back into the retainer on the wheelchair.

CAUTION! The locking button is intentionally countersunk to prevent accidental operation. Always use
an object to press the locking button, never your fingers.

2) 

Depth adjustment of the forearm support:

 Loosen the mounting screws under the forearm support, move

the forearm support and re-tighten the mounting screws (see fig. 64, item 1).

27

Motus CV, Motus CS

Settings

Summary of Contents for Motus CS





































Reviews: