
7
6
• Locate in the foot/heel junction and position before adhesive sets.
• For split toe feet install the heel wedge then remove a thin slice in the
middle by cutting with a sharp knife through the split in the carbon
foot module
(Figure 5)
.
Instant adhesive is necessary to bond the urethane heel wedge. The
adhesive cures in 15-20 seconds.
HEEL ASSEMBLY
If it is necessary to replace the heel component use Loctite 410 and
torque to following specifications:
HEEL DIVIDER
The heel divider should be placed in the last third of the splitted heel
part. To secure its position a drop of instant adhesive can be used on one
side.
BOLT CAP REMOVAL
If it is necessary to remove the bolt cap locate the foot module/bolt cap
junction and use a sharp knife to separate.
FLEX-FOOT SOCK
The toe end of the sock is divided by a thread and fits within the toe split.
Upon fitting the sock, hold the top of the toe thread and slide the sock
into the toe split. The thread of the sock should rest on top of foot
module and not underneath the toe split. The sock should be loose from
the heel area and secured proximally with the cable tie provided.
SHOE HORN (Figure 6 & 7)
When removing and installing the cover use shoehorn to avoid damage
to foot or cover.
MAINTENANCE
The device is designed for low-maintenance. The device should be
inspected every six months for signs of unusual wear, by a prosthetist
familiar with the product.
WEATHERPROOF
A weatherproof device allows use in a wet and/or humid environment
but does not allow submersion. Fresh water splashing against the
enclosure from any direction shall have no harmful effect. Dry thoroughly
after contact with fresh water. Fresh water: Includes tap water. Excludes
salt and chlorinated water.
LIABILITY
The manufacturer recommends using the device only under the specified
conditions and for the intended purposes. The device must be
maintained according to the instructions for use. The manufacturer is
not liable for damage caused by component combinations that were not
authorized by the manufacturer.
Category
Bolt Size
Heel Bolt Tourque
1-4
1/4“
14Nm (10ft-lbs)
Summary of Contents for VARI-FLEX JUNIOR
