![background image](http://html1.mh-extra.com/html/oshkosh-corporation/jlg-es1330l/jlg-es1330l_operation-and-safety-manual_1655774090.webp)
SECTION 6 - OPERATION SPECIFICATIONS AND MAINTENANCE
6-24
31217186
255
PLATFORM OVERLOADED
PF: 5000ms ON/
2000ms OFF
GND: 5000ms
ON/2000ms OFF
2_5
• Drive and Lift Restrictions
•
While the Load Sensing System is enabled, the Platform Load measured by
the Load Sensing System is excessive. Functions from Platform Control Sta
-
tion are prevented, and functions from Ground Control may be prevented,
depending on machine configuration (Markets other than Japan).
•
For the Japanese Market, only Lift Up is prevented and Drive (at creep
speed) is allowed in the stowed position .
•
Refer to LSS functionality for Lift and Drive restrictions.
256
DRIVE PREVENTED – POTHOLE NOT
ENGAGED
PF: 500ms On/
500ms Off
GND: 500ms On/
500ms Off
2_5
• DriveState = PREVENTED
•
While elevated, driving is not possible since the control system detected
that the pot-hole protection mechanism failed to deploy. Clear the obsta
-
cle blocking the pot-hole protection mechanism, repair the mechanical
problem, re-adjust the pot-hole limit switches, or repair the wiring to cor
-
rect the problem.
•
Alternately, there may be difficulty with the Elevation Angle Sensor that
causes the Control System to improperly believe the platform is elevated.
2568
TEMPERATURE CUTOUT ACTIVE - AMBIENT
TEMPERATURE TOO LOW
If Transport
-
Mode = TRUE
PF: Continuous
If Transport
-
Mode = FALSE
PF: OFF
2_5
• Drive and Lift Restrictions
•
The temperature as communicated by the temperature sensor located on
the temperature/tilt sensor is less than or equal to {PERSONALITIES-
>TEMP CUTOUT->CUTOUT SET}
•
(See Low Temperature Cutout Functionality)
•
This DTC shall not be displayed in GroundMode, and no restrictions shall be
implemented.
421
POWER MODULE TOO HOT - PLEASE WAIT None
4_2
• DriveState = PREVENTED
• LiftUpState = PREVENTED
•
Heatsink temperature above 203°F (95° C).
• Possible Cause:
•
Controller is operating in an extreme environment.
•
Excessive load on vehicle.
•
Improper mounting of controller
DTC
Help Message
Alarm
Flash
Code
Action
Trigger
Summary of Contents for JLG ES1330L
