Original Saw Company 3553 Operation & Maintenance Manual Download Page 4

Page: 4 / 35

GENERAL RULES FOR SAFE OPERATION OF POWER TOOLS

KNOW YOUR POWER TOOL

. Read the owner’s manual carefully. Learn the applications and

limitations as well as the specific potential hazards of the tool.

GROUND ALL TOOLS

KEEP GUARDS IN PLACE

. Keep guards in working order.

KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

AVOID DANGEROUS ENVIRONMENTS.

Don’t use power tools in damp or wet locations. Keep

work area well lit.

KEEP CHILDREN AWAY.

All visitors should keep a safe distance from the work area.

DON’T FORCE TOOL.

The tool will do a better job if used at its designed rate.

WEAR PROPER APPAREL.

Loose clothing, gloves or jewelry may get caught in moving parts.

Rubber footwear is recommended when working outdoors.

USE PROTECTIVE GLASSES.

If operation is dusty also wear a dust mask.

10.

DON’T OVER REACH.

Keep proper balance and footing at all times.

11.

MAINTAIN TOOLS WITH CARE.

Tools kept sharp and clean provide the best and safest

performance. Follow instructions for lubricating and changing accessories.

12.

DISCONNECT TOOLS FROM POWER SOURCE.

When not in use, before servicing, when changing

accessories, blades, or cutters, the tool should be disconnected and locked out.

13.

REMOVE ADJUSTING KEYS AND WRENCHES.

Make it a habit to ensure keys and adjusting

wrenches are removed prior to starting tool.

14.

USE RECOMMENDED ACCESSORIES.

Consult your distributor or Original Saw Company for

recommended accessories. Using improper accessories may cause hazards.

15.

SECURE YOUR WORK.

Use clamps or a vise to hold work when practical.

16.

NEVER LEAVE TOOL RUNNING WHILE UNATTENDED.

17.

ONE OPERATOR ONLY.

The person who operates the saw should also position the work.

18.

DO NOT REMOVE SMALL SCRAPS FROM THE TABLE WITH YOUR FINGERS.

POWER TOOL SAFETY

CAUTION

ALL GUARDS MUST REMAIN IN PLACE FOR SAFE CUTTING OPERATON.

NOTE:

This manual is not totally comprehensive. It does not and

cannot cover every possible safety and operational factor

which may arise during the life of the machine.

Summary of Contents for 3553




































Search results

Summary of Contents for 3553

Reviews:

Related manuals for 3553

Brands by name

Popular brands

Original Saw Company 3553, Operation & Maintenance Manual

Search results

Summary of Contents for 3553

Reviews:

Related manuals for 3553

Brands by name

Popular brands