manualshive.com logo in svg

Orientalmotor BXII Series, Operating Manual

Share
Download
Orientalmotor BXII Series Operating Manual Download Page 15

When using the product with the speed control mode 

−15−

•

•

Load factor (Unit: %)

The motor generating torque can be checked. The present load factor is displayed based on the rated torque being 

100%.

•

•

Operation data number

The operation data number corresponding to the present operation can be checked.

•

•

Alarm

When an alarm generates, a corresponding alarm code will be displayed.

The present alarm can be reset, and also alarm records can be checked or cleared.

 

Alarm record 1 (latest)

Alarm record 10 

(oldest)

Alarm record 2

Alarm

Alarm reset

An alarm is being 

reset (blinking)

Clear alarm records

Alarm records are 

being cleared (blinking)

*•

If operations are limited by the edit lock function, the screens in gray color are not displayed.

Note

 

•

Do not turn off the driver power while an alarm is being reset or alarm records are being cleared 

(=while the display is blinking). Doing so may damage the data.

 

•

Some alarms cannot be reset using the 

OPX-2A

. Check by the following table. To reset these 

alarms, cycle the driver power.

Alarm code list

Code

Alarm name

Reset using the 

OPX-2A

10

Excessive position deviation

Possible

20

Overcurrent

Not possible

22

Overvoltage

25

Undervoltage

Possible

28

Sensor error

Not possible

2D

Main circuit output error

30

Overload

Possible

31

Overspeed

41

EEPROM error

Not possible

42

Sensor error at power-on

46

Prevention of operation at power-on

Possible

51

Regeneration unit overheat

Not possible

67

Software overtravel

Possible

70

Operation data error

Summary of Contents for BXII Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands