background image

 

HL-14040-4

 

O P E R A T I N G   M A N U A L 

 

Motorized Actuator Driver 
DC power input Pulse input type 

LSD-K 

Thank you for purchasing an Oriental Motor product. 

This Operating Manual describes product handling procedures and 
safety precautions. 

• 

Please read it thoroughly to ensure safe operation. 

• 

Always keep the manual where it is readily available. 

 

Introduction 

• 

Only qualified personnel should work with the product. Use the 
product correctly after thoroughly reading the separate manual 
BEFORE USING THE PRODUCT. 
The product described in this manual has been designed and 
manufactured for use in general industrial equipment. Do not use 
for any other purpose. Oriental Motor Co., Ltd. is not responsible 
for any damage caused through failure to observe this warning. 

• 

The driver model 

LSD-K

 is a driver common to the 

DG

 Series 

and 

EAS

 Series. 

 

Operating manual types 

Operating manuals for the Motorized Actuator Driver DC power 
input Pulse input type are listed below. 
Use the product correctly after thoroughly reading the operating 
manuals. 

 

Operating Manual name 

EAS

 

Series 

DG

 

Series 

BEFORE USING THE PRODUCT

 

Supplied with 

the product 

 

DG

Series Actuator Edition 

OPERATING MANUAL 

 

Supplied with 

the product

EAS 

Series OPERATING MANUAL 

Supplied with 

the product 

 

EAS 

Series 

CHECKING THE PRODUCT

 

Supplied with 

the product 

 

Motorized Actuator Driver 

DC power input    Pulse input type 

OPERATING MANUAL 

(this document)

 

Supplied with 

the product 

Supplied with 

the product

AR

 Series DC power input 

Pulse input type USER MANUAL

 

 

 

∗ 

The USER MANUAL for this product is in common with the 

AR

 Series. 

This manual does not come with the product. For details, contact your 
nearest Oriental Motor sales office. 

 

CE Marking 

• 

Low Voltage Directives 

Because the input power supply voltage of this product is 24 VDC

,

 it 

is not subject to the Low Voltage Directive but install and connect 
this product as follows. 

• 

This product is designed and manufactured to be installed within 
another device. Install the product in an enclosure. 

• 

For the driver power supply, use a DC power supply with 
reinforced insulation on its primary and secondary sides. 

• 

EMC Directive 

This product has received EMC compliance under the conditions 
specified in “Example of actuator and driver installation and wiring” 
on USER MANUAL. Since the compliance with the EMC Directive 
of the customer's equipment will be affected by various conditions 
such as the configuration, wiring and layout of the control system 
devices and electrical parts used together with the actuator and 
driver, the customer finally must verify the conformance of the 
equipment by performing EMC Testing. 

• 

Applicable Standards 

EMI 

Emission Tests 
 
Radiated Emission Test 

EN 61000-6-4 
EN 61800-3 C3 
EN 55011 group 1 class A 

EMS 

Immunity Tests 
 
Radiation Field Immunity Test 
Electrostatic Discharge Immunity Test 
Fast Transient / Burst Immunity Test 
Conductive Noise Immunity Test 

EN 61000-6-2 
EN 61800-3 C3 
IEC 61000-4-3 
IEC 61000-4-2 
IEC 61000-4-4 
IEC 61000-4-6 

• 

Machinery Directive (

EAS

 Series only) 

The motorized actuators and drivers have been designed and 
manufactured to be installed within general industrial equipment, 
and a Declaration of Incorporation of Partly Completed Machinery is 
issued with them according to the Machinery Directive. 
Applicable standards: EN ISO 12100 
Noise level: 72 dB 

 

Hazardous substances 

The products do not contain the substances exceeding the restriction 
values of RoHS Directive (2011/65/EU). 

Precautions for use 

This section covers limitations and requirements the user should 
consider when using the product. 

• 

Use the supplied cable to connect the actuator and driver. 

Always use the supplied cable to connect the actuator and driver. 
If a flexible cable or cable of 3 m (9.8 ft.) or longer is to be used, an 
appropriate cable must be purchased separately. 

• 

Motor excitation at power ON 

Simply turning on the power will not excite the motor. To excite the 

motor, always turn the C-ON input ON. 

It is possible to set the actuator to be excited automatically after the 

power has been turned on, by changing the applicable driver 

parameter using the accessory data setter 

OPX-2A

 or data setting 

software 

MEXE02

 (both are sold separately). 

Summary of Contents for LSD-K

















Reviews: