manualshive.com logo in svg

OreaTEL GT48, User Manual, Page: 20 / 55

Share
Download
OreaTEL GT48 User Manual Download Page 20

www.greatel.net

                                                                                                                                                              - 20 - 

 

Figure 4 - 5 

Since straight cable is used, the connector for the other end of the cable can be made the same way using RJ45 
connector. 

Note: Please use shielded CAT-5 cable when option is available for better signal transmission quality. 

After the Ethernet cable is ready, one end of the cable can connect to GT48 and the other end connect to a HUB. 
Please check the Ethernet LED status: yellow means connecting in progress and green means in operation. 

4.6.3 Connecting 

FXS 

Cable 

GT48 has an FXS interface that connects to analog phones. 

Connect one end of the FXS cable to the GT48 FXS interface, and connect the other end to phones, faxes, or 
PBXs, as shown in Figure 4-6.   

 

Figure 4 - 6 Connecting to FXS cable 

Note: When connecting the cable makes sure you connect the right ends. 

4.7 Connecting Power Supply 

GT48 uses high efficient switching power supply module. Single module can power up the unit with full load. The 
second power supply module can also be installed to provide redundancy. The switching power supply module 
has the following characteristics:   

Summary of Contents for GT48
























































Reviews:

No comments